• 48 – 96 VDC Series Motor
• 10 HP @ 72V Continuous Rated *
• 65 Ft /Lbs Torque Peak @ 72V
• 30 HP Peak @ 72V 450 Amp Controller
• 1.125 Single Shaft, 6.7″ Dia by 15.0″ Long
• Actual Weight 83 lbs
• Shipping Weight 98 lbs

* (Reference: D&D Motors Specification)

• For EZ-GO Series
• For use with Stock Tires, Two Seat carts & Flat runs.
• High Speed with Stock Tires
• Series Motor 36 VDC
• 8.6 HP Peak @ 4850 Rpms
• 19 Tooth Female Spline
• Replaces a D297

• For Yamaha Series 1992 & Later
• Speed with Stock Tires
• Series Motor 36 VDC
• 8.6 HP Peak
• 19 Tooth Female Spline

• For Club Car Series 1992 & later
• High Speed with Stock Tires (18″)
• Series Motor 48 VDC
• Approximate Speed 25 mph
• 11.5 HP Peak @ 5800 rpm’s *
• 5-15% increase in torque
• Replaces D380 “Bad Boy”
• 10 Tooth Female Spline

This motor is similar to the GE D380 “Bad Boy” motor.

* (Reference: D&D Motors Specification)

Features include:

• 48-72VDC
• Shunt Motor
• 9 HP @ 72V Continuous Rated
• 60 Ft /Lbs Torque Peak
• 31 HP Peak with a 500 Amp Controller *
• 7/8″ Single Shaft Base / Face-mounted
• 6.7″ Dia by 12.28″ Long
• Actual Weight 62 lbs
• Shipping Weight 70 lbs

This is a very nice fan cooled shunt wound motor that does not need reversing contactors to change direction. It’s all taken care of by the controller.

D&D Motor Systems is the premier EV motor manufacturer in the U.S. for small to medium light-weight electric vehicle (EV) conversions. U.S. made with our high performance EV motors (motors for electric cars) at a cost you can afford!

* (Reference: D&D Motors Specification)

For D&D Motors Documents, see our FAQ and Documents.

• Yamaha YDRE, G19 / G22
• Can run on a E-Z-Go DCS / PDS when used with an Alltrax XCT controller.
• Used on Yamaha vehicles that require more low end torque and better run time.
• Shunt Motor with Regen 48 VDC
• 40-50% increase in torque
• 19 Tooth Female Spline (works with the Dana H12 Axle)
• Length 9.75 inches long, no including speed sensor.
• Actual Weight 48 lbs
• Shipping Weight 50 lbs

Vehicle performance specifications are compared to the standard factory performance. Several factors can effect the performance. Some are battery conditions; tire size, tread type and air pressure and varying environmental conditions. Standard factory speeds normally run between 12 – 14 MPH.

Itâ€Âs recommended that you upgrade wiring throughout the golf cart to a minimum of 4 AWG and a contactor that is rated for 400 amp continuous.

Alltrax has come out with a new set of field maps for the DCX Controllers to maximize the performance of these motors. If you wish to use your current controller it needs to be updated to this new field map or it could cause failure to both the motor & controller. You are welcome to send your controller to us to be programmed for a fee of $15 to pay for shipping the controller back to you.

* (Reference: D&D Motors Specification)

• 72-120 VDC Series Motor
• 10 HP @ 72V Continuous Rated *
• 72 Ft /Lbs Torque Peak
• 30 HP Peak @ 72V 450 Amp Controller
• 54 HP Peak @ 96V 600 Amp Controller
• 62 HP Peak @ 120V 550 Amp Controller
• 1.125 Single Shaft, 6.7″ Dia by 15.0″ Long
• Actual Weight 83 lbs
• Shipping Weight 98 lbs

* (Reference: D&D Motors Specification)

• For Club Car IQ & PD-Plus
• Speed Motor with good torque
• Speeds up to 22 mph
• Approximately 50% increase in torque with a 500 amp controller
• Shunt Motor with Regen 48 VDC
• 10 hp peak
• 10 Tooth Female Spline
• Length 9.75 inches long, 10.5″ with speed sensor
• Weight 58 lbs

Vehicle performance specifications are compared to the standard factory performance. Several factors can effect the performance. Some are battery conditions; tire size, tread type and air pressure and varying environmental conditions. Standard factory speeds normally run between 12 – 14 MPH.

Itâ€Âs recommended that you upgrade wiring throughout the golf cart to a minimum of 4 AWG and a contactor that is rated for 400 amps continuous.

Alltrax has come out with a new set of field maps for the XCT Controllers to maximize the performance of these motors. If you wish to use your current controller it needs to be updated to this new field map or it could cause failure to both the motor & controller. You are welcome to send your controller to us to be programmed for a fee of $15 to pay for shipping the controller back to you.

* (Reference: D&D Motors Specification)